View TDA6190_4986767.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

wireless components dvb-if mixer tda 6190 version 1.2 specification april 2000
edition 03.99 published by infineon technologies ag sc, balanstra?e 73, 81541 mnchen ? infineon technologies ag 19.04.00. all rights reserved. attention please! as far as patents or other rights of third parties are concerned, liability is only assumed for components, not for application s, processes and circuits im- plemented within components or assemblies. the information describes the type of component and shall not be considered as assured characteristics. terms of delivery and rights to change design reserved. due to technical requirements components may contain dangerous substances. for information on the types in question please cont act your nearest infineon technologies office. infineon technologies ag is an approved cecc manufacturer. packing please use the recycling operators known to you. we can also help you ? get in touch with your nearest sales office. by agreeme nt we will take packing material back, if it is sorted. you must bear the costs of transport. for packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for an y costs incurred. components used in life-support devices or systems must be expressly authorized for such purpose! critical components 1 of the infineon technologies ag, may only be used in life-support devices or systems 2 with the express written approval of the infineon technologies ag. 1 a critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life- support device or system, or to affect its safety or effectiveness of that device or system. 2 life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sust ain human life. if they fail, it is reasonable to assume that the health of the user may be endangered. abm ? , aop ? , arcofi ? , arcofi ? -ba, arcofi ? -sp, digitape ? , epic ? -1, epic ? -s, elic ? , falc ? 54, falc ? 56, falc ? -e1, falc ? -lh, idec ? , iom ? , iom ? -1, iom ? -2, ipat ? -2, isac ? -p, isac ? -s, isac ? -s te, isac ? -p te, itac ? , iwe ? , musac ? -a, octat ? -p, quat ? -s, sicat ? , sicofi ? , sicofi ? - 2, sicofi ? -4, sicofi ? -4c, slicofi ? are registered trademarks of infineon technologies ag. ace ? , asm ? , asp ? , potswire ? , quadfalc ? , scout ? are trademarks of infineon technologies ag. revision history: current version: april 2000 previous version:data sheet page (in previous version) page (in current version) subjects (major changes since last revision)
product info product info wireless components specification, april 2000 package tda 6190 product info general description the tda 6190x, tda 6190t and tda 6190s are bipolar integrated circuits for amplification and down conversion of modulated if signals used for dvb on cable or for terrestrial transmission. features input frequency range of 30 to 65 mhz tda 6190x: automatic gain control with integrated peak agc detector tda 6190t, tda 6190s: external gain control for integrated variable gain amplifier tda 6190s: reduced output level output for adjustable delayed tuner agc integrated low noise vco circuitry with external varactor diode or crystal broadband outputs for the down converted if signal internal low noise reference voltage source full esd protection application for use in tv or cable set-top receivers for d igital v ideo b road- cast. ordering information type ordering code package tda 6190x q67100-v2005 p-dso-16-1 tda 6190x q67106-v2005 (tape and reel) p-dso-16-1 tda 6190t q67036-a1073 (tape and reel) p-dso-16-1 tda 6190s q67036-a1125 (tape and reel) p-dso-16-1
1 table of contents 2 product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 2.1 overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.2 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.4 package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 3 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 3.1 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3.2 pin definition and function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 3.3 functional block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -4 3.4 functional blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.1 power supply, reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.2 dvb-if input amplifier, agc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 -5 3.4.3 oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.4 mixer and output buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-5 4 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 4.1 test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 4.2 equivalent i/o schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 -3 4.3 application circuit 1 (evaluation board) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 4.4 application circuit 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 5 reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 5.1 electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.1.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5- 2 5.1.2 operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 5.1.3 ac/dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 5.2 application board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.3 bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 5.4 typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-9
2 product description 2.1 overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.2 application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.3 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.4 package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 contents of this chapter
product description 2 - 2 tda 6190 wireless components specification, april 2000 2.1 overview the tda 6190x, tda 6190t and tda 6190s are bipolar integrated circuits for amplification and down conversion of modulated if signals used for dvb on cable or for terrestrial transmission. 2.2 application for use in tv or cable set-top receivers for d igital v ideo b roadcast. 2.3 features input frequency range of 30 to 65 mhz tda 6190x: automatic gain control with integrated peak agc detector tda 6190t, tda 6190s: external gain control for integrated variable gain amplifier tda 6190s: reduced output level output for adjustable delayed tuner agc integrated low noise vco circuitry with external varactor diode or crystal broadband outputs for the down converted if signal internal low noise reference voltage source full esd protection
product description 2 - 3 tda 6190 wireless components specification, april 2000 2.4 package outlines p-dso-16.eps figure 2-1 p-dso-16-1
3 functional description 3.1 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 3.2 pin definition and function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 3.3 functional block diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 3.4 functional blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.1 power supply, reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.2 dvb-if input amplifier, agc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.3 oscillator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 3.4.4 mixer and output buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 contents of this chapter
functional description 3 - 2 tda 6190 wireless components specification, april 2000 3.1 pin configuration pin_config.wmf figure 3-1 pin configuration vref vcob2 vcoe2 vcoe1 vcob1 oscgnd out1 out2 tagcthr tunagc vs ifg nd if1 if2 gnd ifag c 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 tda 6190
functional description 3 - 3 tda 6190 wireless components specification, april 2000 3.2 pin definition and function table 3-1 pin definition and function pin no. symbol function 1 tagcthr tuner agc threshold; delayed tuner agc adjust input; if not required,connect to reference voltage vref 2 tunagc delayed tuner agc output; open npn transistor collector 3 vs supply voltage 4 ifgnd if input ground 5 if1 if input if1; balanced to if2 6 if2 if input if2; balanced to if1 7 gnd ground 8 tda 6190x ifagc if agc filter; automatic gain control filter pin, low voltage corresponds to maxi- mum gain 8 tda 6190t, tda 6190s ifagc if amplifier gain control input pin, low voltage corresponds to maximum gain 9 out2 buffered mixer output out2; balanced to out1 10 out1 buffered mixer output out1; balanced to out2 11 oscgnd oscillator ground 12 vcob1 vco base 1; balanced to vcob2 13 vcoe1 vco emitter 1; balanced to vcoe2 14 vcoe2 vco emitter 2; balanced to vcoe1 15 vcob2 vco base 2; balanced to vcob1 16 vref reference voltage
functional description 3 - 4 tda 6190 wireless components specification, april 2000 3.3 functional block diagram funct_block.wmf figure 3-2 functional block diagram tda 6190x: agc active tda 6190t, tda 6190s: agc disabled, external gain control voltage to pin 8 tagcthr tunagc vs ifg nd if1 if2 gnd ifag c vref vcob2 vcoe2 vcoe1 vcob1 oscgnd out1 out2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 amp agc tuner agc osc mixer
functional description 3 - 5 tda 6190 wireless components specification, april 2000 3.4 functional blocks 3.4.1 power supply, reference voltage the 3.6 v low noise reference voltage vref is used as a reference for the adjust- ment of the delayed tuner agc. the reference voltage has a low temperature coefficient and high line regulation. 3.4.2 dvb-if input amplifier, agc the filtered if signal is fed to the balanced input pins if1 / if2 of the gain con- trolled amplifier, where it is amplified and then down converted to the output fre- quency signals. tda 6190x: the control voltage for the gain-controlled amplifier at pin ifagc is derived from a peak level detector at the down converted outputs. tda 6190t, tda 6190s: the control voltage for the gain-controlled amplifier at pin ifagc is applied from external source. if the ifagc control voltage level exceeds an adjustable value (tagcthr), a sink current at tunagc is generated which controls the tuner gain. 3.4.3 oscillator the symmetrical 4 pin voltage controlled oscillator feeds the mixer to generate the down converted dvb-if signals.the frequency of the vco is below or above the input frequency of the agc amplifier. the control voltage for the external varactor diode is derived from the dvb processor. 3.4.4 mixer and output buffers the mixer converts the filtered and amplified if signal down to the low if fre- quency. this frequency is fed to a balanced output pair out1 and out2.
4 applications 4.1 test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 4.2 equivalent i/o schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 4.3 application circuit 1 (evaluation board) . . . . . . . . . . . . . . . . . . . . . . . 4-4 4.4 application circuit 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 contents of this chapter
applications 4 - 2 tda 6190 wireless components specification, april 2000 4.1 test circuit test_circuit1.wmf figure 4-1 test circuit 1 2 3 4 5 6 7 8 vref vcob2 vs if1 ifgnd ifagc tunagc tag cth r vcoe2 4.5...5.5 v to tuner tda 6190x, tda 6190t gnd out1 from dac of 16 15 14 13 12 11 10 9 51 ? vcoe1 vcob1 oscgnd out2 if2 4.7 100n 100n 100n 10n 10n tp101 100n 120p 39p 39p 100n 1.2k 1.2k 1.2k 1.5n 1.5n 100p bb814 330n gain control voltage dvb-processor tda 6190x, tda 6190t, tda 6190s dvb-processor
applications 4 - 3 tda 6190 wireless components specification, april 2000 4.2 equivalent i/o schematic i_o_scematic.wmf figure 4-2 equivalent i/o schematic 1 2 3 4 5 6 7 89 10 11 12 13 14 15 16 vref vcoe2 vcob2 vs if1 ifg nd gnd tunagc ou t1 ifag c vc oe 1 vcob1 out2 if 2 tagcthr oscgnd
applications 4 - 4 tda 6190 wireless components specification, april 2000 4.3 application circuit 1 (evaluation board) appl_1.wmf figure 4-3 application circuit 1 (evaluation board) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 vref vs if if ifgnd ifagc tunagc ta gc thr 4.5...5.5 v to tuner 36 m hz tda 6190x, tda 6190t gnd vcob2 ou t1 vcob1 vc oe 2 vcoe1 10 k ? oscgnd out2 100n 100n vtune 120p 39p 39p 10k 10k 10k 1n 1n 100p bb814 330n 100n 100n 100n saw filter tda 6190x, tda 6190t, tda 6190s gain control voltage
applications 4 - 5 tda 6190 wireless components specification, april 2000 4.4 application circuit 2 appl_2.wmf figure 4-4 application circuit 2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 vref vs if if ifgnd ifagc tu nag c ta gc thr 4.5...5.5 v to tuner 36 m hz tda 6190x, tda 6190t gnd vcob2 out1 vcob1 vc oe 2 vcoe1 10 k ? crystal : 3rd overtone, at cut 3.3 k ? 15 p 15 p 47 p 42.67 mhz oscgnd out2 100n 100n 100n 100n 100n g a in co ntrol vo lt age saw filter tda 6190x, tda 6190t, tda 6190s
5 reference 5.1 electrical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.1.1 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 5.1.2 operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 5.1.3 ac/dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 5.2 evaluation board layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.3 bill of material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 5.4 typical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 contents of this chapter
reference 5 - 2 tda 6190 wireless components specification, april 2000 5.1 electrical data 5.1.1 absolute maximum ratings the maximal ratings may not be exceeded under any circumstances, not even momentary and individual, as permanent damage to the ic will result. ambient temperature under bias: t a =-20 to +80 c *) according to mil std 883d, method 3015.7 and eos/esd assn. standard s5.1 - 1993 all values are referred to ground (pin), unless stated otherwise. all ground pins must be connected externally. all currents flowing into the ic are positive, out of the ic are negative. table 5-1 absolute maximum ratings parameter symbol limit values unit test conditions min min reference current i vref -10 1 ma tuner agc output v tunagc -0.3 13,2 v ifagc v ifagc -0.3 vref v if input v if1/if2 -0.3 4 v supply voltage v vs -0.3 6 v mixer outputs i out1 /out2 -5 1 ma vco v vco -0.3 4 v vco i vco -3 ma tuner agc threshold v tagcthr -0.3 vref v junction temperature t j 125 c storage temperature t stg -40 125 c thermal resistance r th sa 110 k/w esd protection *) v esd -4 +4 kv hbm
reference 5 - 3 tda 6190 wireless components specification, april 2000 5.1.2 operating range within the operational range the ic operates as described in the circuit description. the ac / dc characteristic limits are not guaranteed. table 5-2 operating range parameter symbol limit values unit test conditions min max supply voltage v vs 4.5 5.5 v input frequency range of if amplifier (-3 db) f if1/if2 30 70 mhz mixer output bandwidth (-1 db) b out1/out2 11 mhz vco frequency range f vco 25 80 mhz depends on application ambient temperature t a -20 80 c
reference 5 - 4 tda 6190 wireless components specification, april 2000 5.1.3 ac/dc characteristics table 5-3 supply voltagev s = 5v, ambient temperaturet amb = 25 c parameter symbol limit values unit test conditions min typ max 1. power supply, reference voltage current consumption vs i vs 35 50 65 ma reference voltage vref v vref 3.3 3.6 3.8 v vref line regulation ? v ref line 30 mv v vs = 4.5 to 5.5 v vref load regulation ? v ref load 30 mv i vref = -0.5 to 0.5ma vref vs temperature ? v ref tem p -30 10 30 mv t a = 0 to 70 c 2. dvb-if input amplifier, agc static characteristics if input voltage v if1/if2 3.2 3.6 3.9 v ifagc voltage (agc min = gain max ) v ifagcg- max 0 0.5 v ifagc voltage (agc max = gain min ) v ifagcg- min 2.5 3.9 v tuner agc threshold active v tagcthr 0 2.0 v tuner agc threshold disable v tagcthr- dis 3.0 v vs v tuner agc threshold current i tagcthr -1 1 a v tagcthr = 0 v tuner agc output current i tunag- con 2.5 3.5 5 ma v tunagc = 0.5 v; v ifagc =1.5v; v tagcthr = 1v tuner agc output current i tunag- coff 0 10 a v tunagc = 13.2 v; v ifagc =1.5v; v tagcthr = 2v dynamic characteristics minimum if input level (max. gain) v min if1/if2 40 44 48 db v f if1/if2 = 36 mhz (sine); v ifagc = 0.4 v; tda 6190x: v out 1 -v out2 set to 2 x 1v pp tda 6190t: v out 1 -v out2 set to 2 x 1v pp tda 6190s: v out1 -v out2 set to 2 x 560mvpp maximum if input level (min. gain) v max if1/if2 88 92 96 db v f if1/if2 = 36 mhz (sine); v ifagc = 2.4 v; tda 6190x: v out 1 -v out2 set to 2 x 1v pp tda 6190t: v out1 -v out2 set to 2 x 1v pp tda 6190s: v out1 -v out2 set to 2 x 560mvpp
reference 5 - 5 tda 6190 wireless components specification, april 2000 table 5-3 supply voltagev s = 5v, ambient temperaturet amb = 25 c (continued) parameter symbol limit values unit test conditions min typ max input impedance *) r if1/if2 c if1/if2 1.5 2.0 1.5 2.5 k ? pf balanced input maximum slope of delayed tuner agc ? i tunagc / ? v ifagc 27 40 54 ma/v v ifagc =1.8 to 2.1v v tagcthr =1.9v v tunagc =0.5v *) design related values 3. oscillator static characteristics vco voltage v vcob1/ vcob2 2.1 2.4 2.7 v dynamic characteristics vco input admittance a y=g+jb vco, 39/120/39pf real part g vcob1 / b2 -1.3 ms f vco = 25 mhz imag. part b vcob1 / b2 1.8 ms f vco = 25 mhz real part g vcob1 / b2 -1.9 ms f vco = 55 mhz imag. part b vcob1 / b2 5.8 ms f vco = 55 mhz oscillator level v vcob1/ b2 107 db v f vco = 43 mhz oscillator range f vco 25 60 mhz depends on application oscillator frequency variation range ? = f vco 4 6 mhz application circuit 1 v tune = 0.5 to 3 v oscillator phase noise @ 10 khz ? vco -105 dbc/ hz application circuit 1 f vco = 43 mhz 4. mixer, output buffers static characteristics demodulator output dc level tda 6190x, tda 6190t v out1 / out2 v vs - 2.5 v vs - 2.0 v vs - 1.5 v demodulator output dc level tda 6190s v out1 / out2 v vs - 2.3 v vs - 1.8 v vs - 1.3 v demodulator output sink current i out1 / out2 1.4 2.0 2.8 ma
reference 5 - 6 tda 6190 wireless components specification, april 2000 table 5-3 supply voltagev s = 5v, ambient temperaturet amb = 25 c (continued) parameter symbol limit values unit test conditions min typ max dynamic characteristics dynamic characteristics tda 6190t: output voltage v out1 -v out2 set to 2 x 1vpp tda 6190s: output voltage v out1 -v out2 set to 2 x 560mvpp tda 6190x: demodulator ac output voltage v out1 0.9 1.0 1.1 v pp f if = 36 mhz; f vco = 43 mhz; r l = 10 k ? ; cl 10 pf; v if1/if2 = 60 db v tda 6190x: demodulator ac output voltage v out2 0.9 1.0 1.1 v pp f if = 36 mhz; f vco = 43 mhz; r l 10 k ? ; cl 10 pf; v if1/if2 = 60 db v mixer output bandwidth ( -1 db ) b out1/ b out2 11 mhz f vco = 43 mhz; r l 10 k ? ; cl 10 pf; v if1/if2 = 60 db v intermodulation a im 40 48 db f vco = 43 mhz; r l 10 k ? ; cl 10 pf; v f 1 = v f 2 = 60 db v f 1 if1/if2 = 37 mhz; f 2 if1/if2 = 38 mhz; out1/out2: balanced harmonic distortion thd -60 -50 db f vco = 43 mhz; r l 10 k ? ; cl 10 pf; v if1/if2 = 70 db v f if1/if2 = 39.5 mhz out1/out2: balanced buffer output impedance r out1 25 100 ? f out1/out2 = 11 mhz buffer output impedance r out2 25 100 ? f out1/out2 = 11 mhz
reference 5 - 7 tda 6190 wireless components specification, april 2000 5.2 evaluation board layout 6190lp3_2.pdf figure 5-1 evaluation board
reference 5 - 8 tda 6190 wireless components specification, april 2000 5.3 bill of material table 5-4 bill of material for application circuit 1 component type / value material / raster outline / case supplier ordering code nr. r01 10k 0805 s&m r02 10k 0805 s&m r03 10k 0805 s&m c01 100n x7r 0805 s&m c02 100n x7r 0805 s&m c03 100n x7r 0805 s&m c04 100n x7r 0805 s&m c05 100n x7r 0805 s&m c06 39p cog 0805 s&m c07 120p cog 0805 s&m c08 39p cog 0805 s&m c09 1n x7r 0805 s&m c10 1n x7r 0805 s&m c11 1f 5mm mkt s&m c12 100p cog 0805 s&m c13 4n7 x7r 0805 s&m tr01 10k potentiom. tr02 10k potentiom. saw01 x6966m saw filter s&m d01 bb814 var. diode l01 330nh filter adjust. toko t1369z ic01 TDA6190x p-dso-16-1 infineon q6600-s-t mechanical parts 1 x pcb 8 x soldering pin 1 mm (stocko) 1 x bnc-jack (pcb mounting)
reference 5 - 9 tda 6190 wireless components specification, april 2000 5.4 typical characteristics TDA6190xts_convgain.pdf TDA6190xts_s2n.pdf tda 6190 conversion gain, balanced input to balanced output ifagc(v) 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 (db) 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 (db) : ifagc(v) gain tda 6190x, tda 6190t gain tda 6190s tda 6190 signal to noise ratio s/n, signal: continuous sine wave, noise: 8mhz bandwidth (db) 0.0 10.0 20.0 30.0 40.0 50.0 60.0 vinput(dbuv) 40.0 45.0 50.0 55.0 60.0 65.0 70.0 75.0 80.0 85.0 90.0 95.0 100.0 0.105k 0.11k 0.115k (db) : vinput(dbuv) s/n, test circuit s/n, application circuit with filter s+m x6966m

▲Up To Search▲

Price & Availability of TDA6190

	To Download TDA6190 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .